QG/FG系列氣流干燥機

應用 Applications

這種類型的設備，適應的物料比較多，除基本型提及的物料外，還有:.A.B.C中間體、A.B.S樹脂、A.S.C、 白碳黑、苯茶毗酮、茶粕、草酸催化劑、促進劑m、d.m、觸媒、沉淀炭粉、對乙酷氮基苯磺酷氨、、哆耳瑪托、對苯二酸、二乙苯按、二氧花、活性碳、氟硅酸鈉、 氟石礦、副產硫按、硅膠粉末、合成樹脂、磺酸鈣、 聚丙烯樹脂、、焦硅酸鈉、糠氯酸咖啡渣、、、硫化礦、磷礦粉、蘭BB、P.V.C、熔融磷肥、 四環素、三氧化鐵、碳酸鈣、欽鐵礦、銅礦、土豆粉、尾煤、硬脂酸鹽、玉米蛋白、藥品、藥劑、氧化鐵、酒渣等。

This type of equipment is suitable for many materials, except those mentioned in the basictype. Also: methaqualone, A.B.C intermediate, A.B.S resin, AS.C, white carbon blackbenzene-tea pyrazolone, tea meal, oxalic acid catalyst, accelerant m, d.m, catalyst.precipitated carbon powder,p-acetylazobenzene sulfony ammonia, p-aminosalicylic acidtolmetol, p-phenylene diacid, diethylbenzene ammonium, titanium dioxide, activated carbon.sodium fluosilicate, fluorspar ore, byproduct ammonium sulfate, silica gel powder, syntheticresin, calcium sulfonate, polypropylene resin, aureomycin, Sodium pyrosilicate, bran chloricacid coffee residue, oral glucose, sodium sulfate, sulfide ore, phosphate rock powder, blueBB, PV.C. molten phosphate fertilizer, tetracvcline, ferric oxide, calcium carbonate, ilmenitecopper ore, potato powder, tail coal, stearate, zein, drugs, pharmaceuticals, iron oxide, wineresidue,etc.

原理 Principles

具有分散作用的風機，特別適合熱敏性物料的氣流干燥作業。高速飛旋的風機葉輪，能把濕的、甚至結塊的物料解碎，直至分散，在分散過程中同時攪拌、混合，然后物料和熱氣流平行地流動。這種類型的設備，適應干燥濾餅結塊的，但還屬于表面水份的物料，含濕量≤40%，如果處理量大或者成品要求干至15%以下時，可采用二級氣流干燥。當物料含濕量超過40%，但<60%時，進料較困難，應采用混料器，通過混進干料的方法以降低進料水份，此時，干燥設備的總產量就有較大幅度的下降，這在經濟上是不合算的。因此，用戶應先用機械的方法(離心脫水或壓濾)盡可能的降低進料水份，以確保干燥作業上的順利進行。

Fan with dispersing function is especially suitable for airflow drying of heat sensitivematerials.The high-speed whirling fan impellercan break up wet or even cakedmaterials until they are dispersed,stir and mix atthe sametime during the dispersionprocess, and then the materials and hot air flow in parallel.This type of equipment issuitable for drving materials with caked filter cakes, but also with surface moisturecontent less than or equal to 40%. if the treatment capacity is large or the finishedproduct requires drying below 15%, secondary air flow drying can be adopted. Whenthe moisture content of the material exceeds 40%, but is less than or equal to 60%, itis more difficult to feed. A mixer should be used to reduce the moisture content of thefeed by mixing dry materials. At this time. the total outout of the drving eauipment wll be greatly reduced, which is uneconomical, Thereforeusers should first use mechanical methods (centrifugal dehydration or pressure flktration) to reduce the feed water as much as possible toensure the smooth progress of drving operations.

技術參數 Technicalparameters

干燥實例 Dried samples